>NAME1>NAME>NAME>NAME>NAME<b>AVR ISP HEADER</b>
<br>
Standard 6 pin header for AVR programming<h3>SparkFun Resistors</h3>
This library contains resistors. Reference designator:R.
<br>
<br>
We've spent an enormous amount of time creating and checking these footprints and parts, but it is <b> the end user's responsibility</b> to ensure correctness and suitablity for a given componet or application.
<br>
<br>If you enjoy using this library, please buy one of our products at <a href=" www.sparkfun.com">SparkFun.com</a>.
<br>
<br>
<b>Licensing:</b> Creative Commons ShareAlike 4.0 International - https://creativecommons.org/licenses/by-sa/4.0/
<br>
<br>
You are welcome to use this library for commercial purposes. For attribution, we ask that when you begin to sell your device using our footprint, you email us with a link to the product being sold. We want bragging rights that we helped (in a very small part) to create your 8th world wonder. We would like the opportunity to feature your device on our homepage.<h3>AXIAL-0.3</h3>
<p>Commonly used for 1/4W through-hole resistors. 0.3" pitch between holes.</p>>Name>Value<p><b>Generic 1608 (0603) package</b></p>
<p>0.2mm courtyard excess rounded to nearest 0.05mm.</p>>NAME>VALUEThis is the "EZ" version of the standard .3" spaced resistor package.<br>
It has a reduced top mask to make it harder to install upside-down.>Name>Value<h3>AXIAL-0.1</h3>
<p>Commonly used for 1/4W through-hole resistors. 0.1" pitch between holes.</p>>Name>Value<h3>AXIAL-0.1-KIT</h3>
<p>Commonly used for 1/4W through-hole resistors. 0.1" pitch between holes.</p>
<p><b>Warning:</b> This is the KIT version of the AXIAL-0.1 package. This package has a smaller diameter top stop mask, which doesn't cover the diameter of the pad. This means only the bottom side of the pads' copper will be exposed. You'll only be able to solder to the bottom side.</p>>Name>ValueAXIAL-0.3
Commonly used for 1/4W through-hole resistors. 0.3" pitch between holes.Generic 1608 (0603) package
0.2mm courtyard excess rounded to nearest 0.05mm.This is the "EZ" version of the standard .3" spaced resistor package.
It has a reduced top mask to make it harder to install upside-down.AXIAL-0.1
Commonly used for 1/4W through-hole resistors. 0.1" pitch between holes.AXIAL-0.1-KIT
Commonly used for 1/4W through-hole resistors. 0.1" pitch between holes.
Warning: This is the KIT version of the AXIAL-0.1 package. This package has a smaller diameter top stop mask, which doesn't cover the diameter of the pad. This means only the bottom side of the pads' copper will be exposed. You'll only be able to solder to the bottom side.>NAME>VALUE<h3>100Ω resistor</h3>
<p>A resistor is a passive two-terminal electrical component that implements electrical resistance as a circuit element. Resistors act to reduce current flow, and, at the same time, act to lower voltage levels within circuits. - Wikipedia</p><b>AVR Microcontrollers</b>
<p>Created by Michael Shimniok <a href="http://www.bot-thoughts.com/">www.bot-thoughts.com</a></b>>VALUE>NAME>NAME>VALUE<b>ATtiny441, ATtiny841 AVR Microcontroller</b>
<p>The high-performance Atmel picoPower 8-bit AVR RISC-based microcontroller combines 4KB ISP
flash memory, 512-Byte EEPROM, 128B SRAM, 12 general purpose I/O lines, 32 general purpose
working registers, an 8-bit timer/counter with two PWM channels, two 16-bit timer/counters with
two PWM channels, internal and external interrupts, an 12-channel 10-bit A/D converter, 2 On-chip
analog comparators, 2 full duplex USARTs with Start Frame wake up from power down, master/slave
SPI serial interface, slave I2C serial interface, programmable gain stage (1x, 20x, and 100x) for
12 differential ADC channel pairs, programmable watchdog timer with internal oscillator, internal
calibrated oscillator, and four software selectable power saving modes. The device operates
between 1.7-5.5 volts.</p>
<a href="http://www.atmel.com/Images/Atmel-8495-8-bit-AVR-Microcontrollers-ATtiny441-ATtiny841_Datasheet.pdf">datasheet.pdf</a><b>Pin Header Connectors</b><p>
<author>Created by librarian@cadsoft.de</author><b>PIN HEADER</b>>NAME>VALUE<b>PIN HEADER</b>>NAME>VALUEPIN HEADERPIN HEADER>NAME>VALUE<b>PIN HEADER</b><b>https://componentsearchengine.com</b><p>
<author>Created by SamacSys</author><b>BAT-HLD-001</b><br>
>NAME>VALUE>NAME>VALUE<b>Coin Cell Battery Holders Linx CR2032 Battery Holder</b><p>
Source: <a href="https://componentsearchengine.com/Datasheets/1/BAT-HLD-001.pdf"> Datasheet </a>
Since Version 8.2, EAGLE supports online libraries. The ids
of those online libraries will not be understood (or retained)
with this version.
Since Version 8.3, EAGLE supports URNs for individual library
assets (packages, symbols, and devices). The URNs of those assets
will not be understood (or retained) with this version.
Since Version 8.3, EAGLE supports the association of 3D packages
with devices in libraries, schematics, and board files. Those 3D
packages will not be understood (or retained) with this version.